Watch for a plumb level or nothing sticking out from side to side. Place your level against the wall horizontally.Step #3C Identify any horizontal bumps in the wall. By measuring from the vertical high point, your cabinets will remain plumb and level along the wall.You want to make sure upper and lower cabinets line up when installed. Measure from the high point in the wall over to where both upper and lower cabinet runs will end –for example, next to the stove.Work your way around the room, and as you go, mark the wall for a high spot or where the level is flat at the top compared to the bottom.Watch for a plumb level or nothing sticking out from top to bottom. Place your level against the wall vertically.Step #3B Identify any vertical bumps in the wall. You will use the higher point as your reference mark.įollow this process carefully to ensure you end up with level and plumb cabinets and countertops. Compare the high points on the front of the cabinets with the back, along the wall.Repeat the above process 24 inches from the wall and run the straight edge or level parallel to the wall where the front cabinet edge will end.Then mark the floor to indicate the high spot. Shim the low end of the level until you get a level reading. ![]() The level will give you a plane of reference to work with as you go around the room. Lay a straight 8-foot-long, 2-inch x 4-inch board on the floor against the wall, then place a carpenter’s level or laser level on top of it.You can always place shims underneath a cabinet to make it level, which is much easier than cutting it down to level with the floor. To ensure a level installation throughout the kitchen, you’ll need to identify the high spot on the floor and start your installation at that point. Over time a house settles, and the floor can develop a subtle slope. This important pre-installation work will catch any problems before they arise – don’t skip it! Step #3A Locate any high spots on the floor. Each cabinet after that should take between 15-20 minutes to put together. Your first cabinet assembly may take 35-40 minutes. If you’re working with RTA cabinets for the first time, view our step-by-step assembly videos for specific guidance on cabinet assembly. Step #2 Assemble your RTA kitchen cabinets. Before installation, you’ll first need to assemble your cabinets. Count all shelves, trim pieces, filler strips, hardware –brackets, drawer glides, and hinges – to ensure you have all parts. If you ordered ready-to-assemble (RTA) kitchen cabinets, inspect boxes, doors, and drawer fronts for any damage. If you ordered extra trim or filler strips, be sure they were included. Check each unit to look for any damage to the cabinet box, shelves, drawer fronts, and doors. For pre-assembled cabinets, be sure all of the parts are attached. When your cabinets arrive, open up the packing and inspect each piece to confirm you’ve received the correct sizes, color, and style that you ordered. Step #18: Now that base and wall cabinets are installed, you can install finishing molding, crown, scribe, and toekick. Step #17: Drill holes in the cabinets doors for your handles and pulls. ![]() Step #15: Install remaining base cabinets. Step #13: Repeat the process for base cabinets Step #12: Drill holes in the cabinets doors for your handles and pulls. Step #8: Begin corner cabinet installation Step #5: Installing the upper wall cabinets first. Step #4: Place a mark on the wall where the top of the base cabinets will stop. Use these standard tools and supplies for cabinet assembly and installation. Painting walls and trim first will ensure that the cabinets don’t get splattered. If you plan to paint the kitchen as part of your renovation project, consider doing that before installing your new kitchen cabinets. As a DIY team, you can review each step of the job before you begin and set the stage for a successful installation. Your cabinet installation will go more smoothly if you have a second person on hand to help you. This step-by-step cabinet installation guide will explain which tools to use, any extra supplies you’ll need, and how to prepare the space before installation can begin. ![]() Follow this step-by-step guide to getting started on the right track and admire a job well done when you’re finished. However, with clear instructions, enough time, and standard tools, you really can do it yourself. Installing kitchen cabinets is a major project.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |